Cisco 200-301 Exam Dumps Update | Occupy An Excellent Position To Get A High Score

Cisco 200-301 Exam Dumps

To take the Cisco 200-301 exam, you must have practical skills to gain confidence in passing the exam. The 200-301 exam dumps help you identify your strengths and weaknesses so you know where to focus when preparing for your exam!

Pass4itSure has compiled the latest 200-301 exam dumps https://www.pass4itsure.com/200-301.html with 1205 latest 200-301 practice questions to provide you with complete knowledge of the CCNA 200-301 exam. Once you’re familiar with the 200-301 exam mode and difficulty, you’re firmly in the perfect position to get a high score!

What you need to know

As Cisco grows and grows, more and more Cisco CCNA 200-301 certifications appear around every corner. As a result, candidates face great difficulty in passing the CCNA 200-301 exam.

The latest 200-301 exam dumps understand the difficulties of test takers, and it can easily help you achieve test success.

But you don’t know how to get started

The 200-301 exam dumps will make it easier for you.

Before you begin, you need to answer three main questions: why do you need 200-301 exam dumps, which dumps are good, and where to get them? Finally, be sure to take the necessary action – practice the exam questions.

In fact, the first question should be answered at the beginning.

Next, let’s discuss which 200-301 exam dumps are good.

The best 200-301 exam dumps should contain the following:

  • This is the latest 200-301 exam study material integration.
  • Have the latest 200-301 exam practice questions that are all about real exam content.
  • It is a collection of questions distilled by expert preparation and continuous feedback.
  • There are no outdated, duplicated exam questions.

The above Pass4itSure 200-301 exam dumps meet the requirements, you can try them!

Where to get it?

The most important thing to get CCNA 200-301 certification is to improve yourself and get a better salary. So how do you get a high score? You need to find the correct 200-301 exam dumps, and here is the recommended Pass4itSure website. Pass4itSure 200-301 exam dumps are your best bet to get a high score on the exam.

Latest CCNA 200-301 Free Dumps Practice Test Questions (1-15)

Question 1:

By default, how long will the switch continue to know a workstation MAC address after the workstation stops sending traffic?

A. 200 seconds

B. 300 seconds

C. 600 seconds

D. 900 seconds

Correct Answer: B


Question 2:

Which IPv6 address type communication between subnets cannot route on the Internet?

A. link-local

B. unique local

C. multicast

D. global unicast

Correct Answer: B

An IPv6 Unique Local Address is an IPv6 address in the block FC00::/7. It is the approximate IPv6 counterpart of the IPv4 private address. It is not routable on the global Internet.

Note: In the past, Site-local addresses (FEC0::/10) are equivalent to private IP addresses in IPv4 but now they are deprecated.

Link-local addresses are only used for communications within the local subnet. It is usually created dynamically using a link-local prefix of FE80::/10 and a 64-bit interface identifier (based on a 48-bit MAC address).


Question 3:

Refer to the exhibit. Which command configures a floating static route to provide a backup to the primary link?

CCNA 200-301 exam practice test questions 3

A. ip route 0.0.0.0 0.0.0.0 209.165.202.131

B. ip route 209.165.201.0 255.255.255.224 209.165.202.130

C. ip route 0.0.0.0 0.0.0.0 209.165.200.224

D. ip route 209.165.200.224 255.255.255.224 209.165.202.129 254

Correct Answer: D


Question 4:

Which command can you enter to allow Telnet to be supported in addition to SSH?

A. transport input telnet ssh

B. transport input telnet

C. no transport input telnet

D. privilege level 15

Correct Answer: A


Question 5:

You have configured a router with an OSPF router ID, but its IP address still reflects the physical interface. Which action can you take to correct the problem in the least disruptive way?

A. Reload the OSPF process

B. Specify a loopback address

C. Reboot the router

D. Save the router configuration

Correct Answer: A

Once an OSPF Router ID selection is done, it remains there even if you remove it or configure another OSPF Router ID. So the least disruptive way is to correct it using the command “clear ip ospf process”.


Question 6:

What is the collapsed layer in collapsed core architectures?

A. core and distribution

B. distribution and access

C. core and WAN

D. access and WAN

Correct Answer: A


Question 7:

What are the two advantages of implementing a controller-based architecture instead of traditional network architecture? (Choose two.)

A. It allows for seamless connectivity to virtual machines.

B. It increases security against denial-of-service attacks.

C. It supports complex and high-scale IP addressing schemes.

D. It enables configuration task automation.

E. It provides increased scalability and management options.

Correct Answer: DE


Question 8:

What is the purpose of a southbound API in a control-based networking architecture?

A. Facilities communication between the controller and the applications

B. Facilities communication between the controller and the networking hardware

C. allows application developers to interact with the network

D. integrates a controller with other automation and orchestration tools.

Correct Answer: B

The Southbound Interface

In a controller-based network architecture, the controller needs to communicate to the networking devices. In most network drawings and architecture drawings, those network devices typically sit below the controller, as shown in Figure 16-5.

There is an interface between the controller and those devices, and given its location at the bottom part of drawings, the interface came to be known as the southbound interface, or SBI, as labeled in Figure 16-5.

CCNA 200-301 exam practice test questions 8

Question 9:

Refer to the exhibit. What commands are needed to add a subinterface to Ethernet0/0 on R1 to allow for VLAN 20, with IP address 10.20.20.1/24?\

CCNA 200-301 exam practice test questions 9

A. R1(config)#interface ethernet0/0 R1(config)#encapsulation dot1q 20 R1(config)#ip address 10.20.20.1 255.255.255.0

B. R1(config)#interface ethernet0/0.20 R1(config)#encapsulation dot1q 20 R1(config)#ip address 10.20.20.1 255.255.255.0

C. R1(config)#interface ethernet0/0.20 R1(config)#ip address 10.20.20.1 255.255.255.0

D. R1(config)#interface ethernet0/0 R1(config)#ip address 10.20.20.1 255.255.255.0

Correct Answer: B


Question 10:

CCNA Lab simulation 3

IP connectivity between the three routers is configured. OSPF adjacencies must be established.

1. Configure R1 and R2 Router IDs using the interface IP addresses from the link that is shared between them.

2. Configure the R2 links with a max value facing R1 and R3. R2 must become the DR. R1 and R3 links facing R2 must remain with the default OSPF configuration for DR election. Verify the configuration after clearing the OSPF process.

3. Using a host wildcard mask, configure all three routers to advertise their respective Loopback1 networks.

4. Configure the link between R1 and R3 to disable their ability to add other OSPF routers.

A. Check the below

B. Place Holder

C. Place Holder

D. Place Holder

Correct Answer: A

on R1

conf terminal interface Loopback0 ip address 10.10.1.1 255.255.255.255 ! interface Loopback1 ip address 192.168.1.1 255.255.255.0 ! interface Ethernet0/0 no shut ip address 10.10.12.1 255.255.255.0 ip ospf 1 area 0 duplex auto! interface Ethernet0/1 no shut ip address 10.10.13.1 255.255.255.0 ip ospf 1 area 0 duplex auto! router ospf 1 router-id 10.10.12.1 network 10.10.1.1 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 ! copy run star

On R2

conf terminal interface Loopback0 ip address 10.10.2.2 255.255.255.255 ! interface Loopback1 ip address 192.168.2.2 255.255.255.0 ! interface Ethernet0/0 no shut ip address 10.10.12.2 255.255.255.0 ip ospf priority 255 ip ospf 1 area 0 duplex auto! interface Ethernet0/2 no shut ip address 10.10.23.2 255.255.255.0 ip ospf priority 255 ip ospf 1 area 0 duplex auto! router ospf 1 network 10.10.2.2 0.0.0.0 area 0 network 192.168.2.0 0.0.0.255 area 0 ! copy runs start

On R3

conf ter interface Loopback0 ip address 10.10.3.3 255.255.255.255 ! interface Loopback1 ip address 192.168.3.3 255.255.255.0 ! interface Ethernet0/1 no shut ip address 10.10.13.3 255.255.255.0 ip ospf 1 area 0 duplex auto! interface Ethernet0/2 no shut ip address 10.10.23.3 255.255.255.0 ip ospf 1 area 0 duplex auto! router ospf 1 network 10.10.3.3 0.0.0.0 area 0 network 192.168.3.0 0.0.0.255 area 0 ! copy run start !

Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured:

1. Configure an LACP EtherChannel and number it as 1; configure it between switches SW1 and SVV2 using interfaces Ethernet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends

2. Configure the EtherChannel as a trunk link.

3. Configure the trunk link with 802.1 q tags.

4. Configure the native VLAN of the EtherChannel as VLAN 15.

CCNA 200-301 exam practice test questions 10

This ACL is configured to allow client access only to HTTP, HTTPS, and DNS services via UDP. The new administrator wants to add TCP access to the ONS service. Which configuration updates the ACL efficiently?

A. no ip access-list extended Services ip access-list extended Services 30 permit tcp 10.0.0.0 0.255.255.255 host 198.51.100.11 eq domain

B. ip access-list extended Services 35 permit tcp 10.0.0.0 0.255.255.255 host 198.51.100.11 eq domain

C. ip access-list extended Services permit tcp 10.0.0.0 0.255.255.255 host 198.51.100.11 eq domain

D. no ip access-list extended Services

ip access-list extended Services

permit udp 10.0.0.0 0.255.255.255 any eq 53

permit tcp 10.0.0.0 0.255.255.255 host 198.51.100.11 eq domain

deny ip any any log

Correct Answer: D


Question 12:

What are two features of the DHCP relay agent? (Choose two.)

A. assigns DNS locally and then forwards requests to the DHCP server

B. permits one IP helper command under an individual Layer 3 interface

C. allows only MAC-to-IP reservations to determine the local subnet of a client

D. minimizes the necessary number of DHCP servers

E. configured under the Layer 3 interface of a router on the client subnet

Correct Answer: BE


Question 13:

What are the two fundamentals of virtualization? (Choose two.)

A. It allows logical network devices to move traffic between virtual machines and the rest of the physical network.

B. It allows multiple operating systems and applications to run independently on one physical server.

C. It allows a physical router to directly connect NICs from each virtual machine into the network.

D. It requires that some servers, virtual machines, and network gear reside on the Internet.

E. The environment must be configured with one hypervisor that serves solely as a network manager to monitor SNMP traffic.

Correct Answer: AB

Question 14:

DRAG DROP

Drag and drop the wireless architecture benefits from the left onto the architecture types on the right.

Select and Place:

CCNA 200-301 exam practice test questions 14

Correct Answer:

CCNA 200-301 exam practice test questions 14-2
Question 15:

How is the native VLAN secured in a network?

A. separate from other VLANs within the administrative domain

B. give it a value in the private VLAN range

C. assign it as VLAN 1

D. configure it as a different VLAN ID on each end of the link

Correct Answer: A


The latest CCNA 200-301 PDF is free to download: https://drive.google.com/file/d/1_cRoAyec2CHnwI5mExIJHV6REAbNOEyR/view?usp=share_link

I hope the above free questions are useful to you! These questions remain a valuable resource for those who are preparing for the CCNA 200-301 exam. Shared by Pass4itSure.

Lastly

The updated 200-301 exam dumps can help you get a good position to score high on the CCNA 200-301 exam.

So, come to Pass4itSure to get the latest 200-301 exam dumps https://www.pass4itsure.com/200-301.html to pass your exam. Very helpful in improving confidence levels.